permission denied
-
Постов
35 -
Зарегистрирован
-
Посещение
Никогда
Сообщения, опубликованные permission denied
-
-
даю как есть:
[root@host root]# /usr/sbin/pppd call gprs
Serial connection established.
Using interface ppp0
Connect: ppp0 <--> /dev/ttyUSB0
local IP address 172.27.189.139
remote IP address 192.168.254.254
primary DNS address 217.119.94.4
secondary DNS address 217.119.95.2
[root@host root]# /sbin/route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.254.254 * 255.255.255.255 UH 0 0 0 ppp0
169.254.0.0 * 255.255.0.0 U 0 0 0 lo
127.0.0.0 * 255.0.0.0 U 0 0 0 lo
default * 0.0.0.0 U 0 0 0 ppp0
default 192.168.254.254 0.0.0.0 UG 0 0 0 ppp0
[root@host root]# /sbin/iptables -L
Chain INPUT (policy ACCEPT)
target prot opt source destination
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
[root@host root]#
-
Ситуация такая: дозваниваюсь по модему до провайдера, устанавливается соединение, он даёт мне свой IP адрес, мой локальный айпишник, и адреса DNS. А дальше что ни делаю, вообще никуда попасть не могу: ни по одному адресу пакеты не идут, не пингуется ни один удалённый адрес, соответственно в инет тоже не выйти.
Таблица маршрутизации после установки соединения перестраивается, фаервол вообще отключен. Где могут быть грабли ?
-
Даю после:
(то что в /etc/fstab, насколько я знаю Linux, к usbserial
имеет отношение ну очень отдалённое, а тем более разделы NTFS,
это сейчас не является проблемой.)
modprobe usbserial
modprobe pl2303
dmesg:
> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
vesafb: probe of vesafb0 failed with error -6
Machine check exception polling timer started.
Starting balanced_irq
audit: initializing netlink socket (disabled)
audit(1128720934.875:0): initialized
udf: registering filesystem
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
ACPI: Thermal Zone [THRM] (46 C)
Linux agpgart interface v0.100 © Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST3120026A, ATA DISK drive
hdb: IC35L020AVER07-0, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
hdd: IC35L020AVER07-0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
hdb: max request size: 128KiB
hdb: 40188960 sectors (20576 MB) w/1916KiB Cache, CHS=42528/15/63, UDMA(100)
hdb: hdb1 hdb2
hdd: max request size: 128KiB
hdd: 40188960 sectors (20576 MB) w/1916KiB Cache, CHS=42528/15/63, UDMA(100)
hdd: hdd1 hdd2
libata version 1.02 loaded.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC).
ALSA device list:
No soundcards found.
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 300 bytes per conntrack
ip_tables: © 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: © 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
Software Suspend has malfunctioning SMP support. Disabled
ACPI: (supports S0 S1 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 176k freed
Real Time Clock Driver v1.12
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:1d.7: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: capability 0001 at 68
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 201, pci mem e082c000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
usb usb1: Manufacturer: Linux 2.6.7-ck2 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1d.0: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 169, io base 0000e300
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: detected 2 ports
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
usb usb2: Manufacturer: Linux 2.6.7-ck2 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x501
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
uhci_hcd 0000:00:1d.1: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
hub 1-0:1.0: port 1 not reset yet, waiting 50ms
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 193, io base 0000e000
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: detected 2 ports
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: default language 0x0409
usb usb3: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
usb usb3: Manufacturer: Linux 2.6.7-ck2 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 1-1: new high speed USB device using address 2
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: default language 0x0409
usb 1-1: Product: Flash Disk
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
usb 1-1: Manufacturer: USB
uhci_hcd 0000:00:1d.2: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
usb 1-1: SerialNumber: FCA4B93FF261E01F
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
ehci_hcd 0000:00:1d.7: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 177, io base 0000e100
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x501
Initializing USB Mass Storage driver...
usb-storage 1-1:1.0: usb_probe_interface
usb-storage 1-1:1.0: usb_probe_interface - got id
uhci_hcd 0000:00:1d.2: detected 2 ports
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: default language 0x0409
usb usb4: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
usb usb4: Manufacturer: Linux 2.6.7-ck2 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
usb usb4: hotplug
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Generic Model: USB Disk Flash Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
SCSI device sda: 511488 512-byte hdwr sectors (262 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: unknown partition table
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
ehci_hcd 0000:00:1d.7: port 2 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 3: delay 100ms stable 4 status 0x501
uhci_hcd 0000:00:1d.3: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
hub 1-0:1.0: port 3 not reset yet, waiting 50ms
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 169, io base 0000e200
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: detected 2 ports
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: default language 0x0409
usb usb5: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
usb usb5: Manufacturer: Linux 2.6.7-ck2 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
usb usb5: hotplug
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: hotplug
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
uhci_hcd 0000:00:1d.0: port 2 portsc 0093
hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
usb 2-2: new full speed USB device using address 2
usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: default language 0x0409
usb 2-2: Product: USB-Serial Controller
usb 2-2: Manufacturer: Prolific Technology Inc.
usb 2-2: hotplug
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
usb 2-2:1.0: hotplug
uhci_hcd 0000:00:1d.1: port 1 portsc 0093
hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbserial 2-2:1.0: usb_probe_interface
usbserial 2-2:1.0: usb_probe_interface - got id
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for PL-2303
pl2303 2-2:1.0: usb_probe_interface
pl2303 2-2:1.0: usb_probe_interface - got id
pl2303 2-2:1.0: PL-2303 converter detected
usb 2-2: PL-2303 converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
usbcore: registered new driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.10
hub 3-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101
EXT3 FS on hda5, internal journal
usb 3-1: new full speed USB device using address 2
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
usb 3-1: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-1: hotplug
usb 3-1: adding 3-1:1.0 (config #1, interface 0)
usb 3-1:1.0: hotplug
hub 3-1:1.0: usb_probe_interface
hub 3-1:1.0: usb_probe_interface - got id
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 2 ports detected
hub 3-1:1.0: standalone hub
hub 3-1:1.0: individual port power switching
hub 3-1:1.0: individual port over-current protection
hub 3-1:1.0: power on to power good time: 100ms
hub 3-1:1.0: hub controller current requirement: 100mA
hub 3-1:1.0: 400mA bus power budget for children
hub 3-1:1.0: enabling power on all ports
ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
hub 1-0:1.0: port 2, status 0000, change 0001, 12 Mb/s
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
hub 1-0:1.0: port 3, status 0000, change 0001, 12 Mb/s
uhci_hcd 0000:00:1d.2: suspend_hc
uhci_hcd 0000:00:1d.3: suspend_hc
Unable to load NLS charset iso8859-1
Unable to load NLS charset iso8859-1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: hda7: found reiserfs format "3.6" with standard journal
ReiserFS: hda7: using ordered data mode
ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda7: checking transaction log (hda7)
ReiserFS: hda7: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SGI XFS with ACLs, security attributes, realtime, no debug enabled
XFS mounting filesystem hdb2
Ending clean XFS mount for filesystem: hdb2
NTFS driver 2.1.14 [Flags: R/O MODULE].
NTFS-fs warning (device hda1): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.0.
NTFS-fs warning (device hda2): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.0.
NTFS-fs warning (device hdd2): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.0.
Supermount version 2.0.4 for kernel 2.6
Adding 516088k swap on /mnt/swap/x/pagefile.sys. Priority:-1 extents:1
Adding 516088k swap on /mnt/swap/y/pagefile.sys. Priority:-2 extents:2
parport0: PC-style at 0x378 [PCSPP(,...)]
inserting floppy driver for 2.6.7-ck2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xd000, 00:04:61:6d:e6:65, IRQ 225
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xd000, 00:04:61:6d:e6:65, IRQ 225
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
parport0: PC-style at 0x378 [PCSPP(,...)]
lp0: using parport0 (polling).
-
до modprobe. В моём случае разницы никакой - что так, что эдак не работает.
Модули usbserial, pl2303 абсолютно точно.
-
1. Под виндой пашет 100%. на той же машине.
2. А что туда можно послать, чтобы убедиться, что всё работает.
ATZ ? Из десятка 100% рабочих скритпов именно под Siemens S55 у
меня не заработал ни один.
3. dmesg:
> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
vesafb: probe of vesafb0 failed with error -6
Machine check exception polling timer started.
Starting balanced_irq
audit: initializing netlink socket (disabled)
audit(1128717824.874:0): initialized
udf: registering filesystem
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
ACPI: Thermal Zone [THRM] (46 C)
Linux agpgart interface v0.100 © Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST3120026A, ATA DISK drive
hdb: IC35L020AVER07-0, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
hdd: IC35L020AVER07-0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
hdb: max request size: 128KiB
hdb: 40188960 sectors (20576 MB) w/1916KiB Cache, CHS=42528/15/63, UDMA(100)
hdb: hdb1 hdb2
hdd: max request size: 128KiB
hdd: 40188960 sectors (20576 MB) w/1916KiB Cache, CHS=42528/15/63, UDMA(100)
hdd: hdd1 hdd2
libata version 1.02 loaded.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC).
ALSA device list:
No soundcards found.
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 300 bytes per conntrack
ip_tables: © 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: © 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
Software Suspend has malfunctioning SMP support. Disabled
ACPI: (supports S0 S1 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 176k freed
Real Time Clock Driver v1.12
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:1d.7: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: capability 0001 at 68
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 201, pci mem e082c000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
usb usb1: Manufacturer: Linux 2.6.7-ck2 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1d.0: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 169, io base 0000e300
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: detected 2 ports
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
usb usb2: Manufacturer: Linux 2.6.7-ck2 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x501
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
uhci_hcd 0000:00:1d.1: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
hub 1-0:1.0: port 1 not reset yet, waiting 50ms
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 193, io base 0000e000
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: detected 2 ports
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: default language 0x0409
usb usb3: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
usb usb3: Manufacturer: Linux 2.6.7-ck2 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 1-1: new high speed USB device using address 2
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: default language 0x0409
usb 1-1: Product: Flash Disk
usb 1-1: Manufacturer: USB
usb 1-1: SerialNumber: FCA4B93FF261E01F
usb 1-1: hotplug
uhci_hcd 0000:00:1d.2: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
ehci_hcd 0000:00:1d.7: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 177, io base 0000e100
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: detected 2 ports
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: default language 0x0409
usb usb4: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
usb usb4: Manufacturer: Linux 2.6.7-ck2 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
usb usb4: hotplug
Initializing USB Mass Storage driver...
usb-storage 1-1:1.0: usb_probe_interface
usb-storage 1-1:1.0: usb_probe_interface - got id
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Generic Model: USB Disk Flash Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
uhci_hcd 0000:00:1d.3: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x501
SCSI device sda: 511488 512-byte hdwr sectors (262 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: unknown partition table
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
PCI: Setting latency timer of device 0000:00:1d.3 to 64
hub 1-0:1.0: port 2 not reset yet, waiting 50ms
uhci_hcd 0000:00:1d.3: irq 169, io base 0000e200
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: detected 2 ports
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: default language 0x0409
usb usb5: Product: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
usb usb5: Manufacturer: Linux 2.6.7-ck2 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
usb usb5: hotplug
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: hotplug
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
ehci_hcd 0000:00:1d.7: port 2 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 3: delay 100ms stable 4 status 0x501
hub 1-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
uhci_hcd 0000:00:1d.0: port 2 portsc 0093
hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
EXT3 FS on hda5, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
hub 2-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
usb 2-2: new full speed USB device using address 2
usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: default language 0x0409
usb 2-2: Product: USB-Serial Controller
usb 2-2: Manufacturer: Prolific Technology Inc.
usb 2-2: hotplug
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
usb 2-2:1.0: hotplug
uhci_hcd 0000:00:1d.1: port 1 portsc 0093
hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbserial 2-2:1.0: usb_probe_interface
usbserial 2-2:1.0: usb_probe_interface - got id
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for PL-2303
pl2303 2-2:1.0: usb_probe_interface
pl2303 2-2:1.0: usb_probe_interface - got id
pl2303 2-2:1.0: PL-2303 converter detected
usb 2-2: PL-2303 converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
usbcore: registered new driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.10
hub 3-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101
usb 3-1: new full speed USB device using address 2
usb 3-1: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-1: hotplug
usb 3-1: adding 3-1:1.0 (config #1, interface 0)
usb 3-1:1.0: hotplug
hub 3-1:1.0: usb_probe_interface
hub 3-1:1.0: usb_probe_interface - got id
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 2 ports detected
hub 3-1:1.0: standalone hub
hub 3-1:1.0: individual port power switching
hub 3-1:1.0: individual port over-current protection
hub 3-1:1.0: power on to power good time: 100ms
hub 3-1:1.0: hub controller current requirement: 100mA
hub 3-1:1.0: 400mA bus power budget for children
hub 3-1:1.0: enabling power on all ports
ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
hub 1-0:1.0: port 2, status 0000, change 0001, 12 Mb/s
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
hub 1-0:1.0: port 3, status 0000, change 0001, 12 Mb/s
uhci_hcd 0000:00:1d.2: suspend_hc
uhci_hcd 0000:00:1d.3: suspend_hc
Unable to load NLS charset iso8859-1
Unable to load NLS charset iso8859-1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: hda7: found reiserfs format "3.6" with standard journal
ReiserFS: hda7: using ordered data mode
ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda7: checking transaction log (hda7)
ReiserFS: hda7: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SGI XFS with ACLs, security attributes, realtime, no debug enabled
XFS mounting filesystem hdb2
Ending clean XFS mount for filesystem: hdb2
NTFS driver 2.1.14 [Flags: R/O MODULE].
NTFS-fs warning (device hda1): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.0.
NTFS-fs warning (device hda2): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.0.
NTFS-fs warning (device hdd2): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.0.
Supermount version 2.0.4 for kernel 2.6
Adding 516088k swap on /mnt/swap/x/pagefile.sys. Priority:-1 extents:1
Adding 516088k swap on /mnt/swap/y/pagefile.sys. Priority:-2 extents:2
parport0: PC-style at 0x378 [PCSPP(,...)]
inserting floppy driver for 2.6.7-ck2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xd000, 00:04:61:6d:e6:65, IRQ 225
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xd000, 00:04:61:6d:e6:65, IRQ 225
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
parport0: PC-style at 0x378 [PCSPP(,...)]
lp0: using parport0 (polling).
-
Поясняю подробнее:
Все устроства _ЕСТЬ_, отрываются, и в них
посылается какая-то команда (kppp, minicom, pppd, ...).
Но ответ _НЕ_ _ВОЗВРАЩАЕТСЯ_ с этого устройства никогда.
тот же /dev/null, только если шнурок отключить, то уже тогда это устройство пропадает (no such device).
Где грабли ?
-
Абсолютно ничего не говорит о том, как решать проблему:
modprobe pl2303 : <пусто>
modprobe usbserial : <пусто>
и потом вся поддержка может быть builtin в ядре, а не ввиде модулей.
Module Size Used by
ppp_generic 22036 0
slhc 6528 1 ppp_generic
snd_intel8x0 30216 4
snd_ac97_codec 65284 1 snd_intel8x0
snd_mpu401_uart 6656 1 snd_intel8x0
snd_rawmidi 21028 1 snd_mpu401_uart
parport_pc 19520 1
lp 8072 0
parport 21952 2 parport_pc,lp
autofs4 17412 1
sunrpc 134244 1
8139too 20992 0
floppy 52976 0
supermount 35984 2
nls_utf8 1920 4
ntfs 84940 3
xfs 554012 1
vfat 12544 3
fat 39968 1 vfat
pl2303 14852 0
usbserial 24172 1 pl2303
dm_mod 37664 0
sd_mod 16640 0
usb_storage 26880 0
uhci_hcd 29452 0
ehci_hcd 38404 0
rtc 11592 0
-
Ситуация такая: есть GPRS модем в Siemense S55, который надо соеденить ч/з usb шнурок c компом
Проблема: когда втыкаю этот шнурок, драйвер pl2303 не подхватывается,
и, как следствие любой порт usb-serial (/dev/ttyUSB{X}, /dev/usb/tty{X} и др.) виден, но ничего не возвращает, хотя байты туда уходят (как /dev/null). В ядре вся поддержка включена.
Где может быть косяк ?
-
что до, что после lsmod выдаёт одно и тоже:
Module Size Used by
snd_intel8x0 30216 4
snd_ac97_codec 65284 1 snd_intel8x0
snd_mpu401_uart 6656 1 snd_intel8x0
snd_rawmidi 21028 1 snd_mpu401_uart
parport_pc 19520 1
lp 8072 0
parport 21952 2 parport_pc,lp
autofs4 17412 1
sunrpc 134244 1
8139too 20992 0
floppy 52976 0
supermount 35984 2
nls_utf8 1920 4
ntfs 84940 3
xfs 554012 1
vfat 12544 3
fat 39968 1 vfat
dm_mod 37664 0
uhci_hcd 28944 0
ehci_hcd 26244 0
rtc 11592 0
У меня поддержка usbserial прямо в ядро включена, а не в модули
-
Прошу не пинать, если такая тема уже была здесь, но мне
не попалось решение в поиске.
У меня GPRS модем в Siemense S55 ч/з USB датакабель, и так похоже, что модем не отзывается ни на одну команду. Соответствующие драйвера usbserial и поддержка PPP включены в ядре, девайс /dev/ttyUSB0 или /dev/usb/ttyUSB0 тоже открывается,
команды туда уходят, но возвращаются только пустые строки.
Как можно правильно сконфигурить модем?
-
Сканирую со своей машыны :
свой IP :
[root@localhost root]# nmap -sU -vv 192.168.0.1
Starting nmap 3.50 ( http://www.insecure.org/nmap/ ) at 2005-04-26 11:45 UTC
Host 192.168.0.1 appears to be up ... good.
Initiating UDP Scan against 192.168.0.1 at 11:45
The UDP Scan took 5 seconds to scan 1478 ports.
Adding open port 2049/udp
Adding open port 864/udp
Adding open port 911/udp
Adding open port 111/udp
Adding open port 32770/udp
Adding open port 32768/udp
Adding open port 846/udp
Interesting ports on 192.168.0.1:
(The 1471 ports scanned but not shown below are in state: closed)
PORT STATE SERVICE
111/udp open rpcbind
846/udp open unknown
864/udp open unknown
911/udp open unknown
2049/udp open nfs
32768/udp open omad
32770/udp open sometimes-rpc4
Nmap run completed -- 1 IP address (1 host up) scanned in 5.074 seconds
целевую машыну :
[root@localhost root]# nmap -sU -vv 192.168.0.2
Starting nmap 3.50 ( http://www.insecure.org/nmap/ ) at 2005-04-26 11:32 UTC
Host 192.168.0.2 appears to be up ... good.
Initiating UDP Scan against 192.168.0.2 at 11:32
Too many drops ... increasing senddelay to 50000
Too many drops ... increasing senddelay to 100000
Too many drops ... increasing senddelay to 200000
Too many drops ... increasing senddelay to 400000
Too many drops ... increasing senddelay to 800000
# тут всё зависает на неопределённое время, обламываю
caught SIGINT signal, cleaning up
Сейчас убрал одно правило в фаерволе - стало:
со своей машины ч/з интерфейс 192.168.0.1 шара монтируется ОК,
с соседской FreeBSD (192.168.0.3 )- тоже OK,
с целевой машины (192.168.0.2):
[root@SM01 /root]$mount -t nfs 192.168.0.1:/nfsshare /mnt/nfs
nfs warning: mount version older than kernel
lockd_up: no pid, 2 users??
RPC: sendmsg returned error 101
portmap: RPC call returned error 101
RPC: sendmsg returned error 101
portmap: RPC call returned error 101
RPC: sendmsg returned error 101
portmap: RPC call returned error 101
[root@SM01 /root]$
В чём ещё могут быть проблемы ?
-
Вот тут-то турбо-задница. На той стороне нет ничего, кроме ls, mount, df, ping, и терминалка на последовательном порту, а единственный способ чё-нить туда закинуть- примонитировать экспортированную NFS.
Ещё рекомендации ?
-
вроде как открыт:
[root@localhost RPMS]# nmap -sU localhost
Starting nmap 3.50 ( http://www.insecure.org/nmap/ ) at 2005-04-25 15:38 UTC
Interesting ports on localhost (127.0.0.1):
(The 1471 ports scanned but not shown below are in state: closed)
PORT STATE SERVICE
111/udp open rpcbind
666/udp open doom
684/udp open unknown
914/udp open unknown
2049/udp open nfs
32768/udp open omad
32771/udp open sometimes-rpc6
Nmap run completed -- 1 IP address (1 host up) scanned in 5.048 seconds
-
Такая ситуация: надо получить доступ к файловой системе компа
ч/з NFS.
на компе, экспортирующем свою шару через NFS такие настройки в
/etc/exports :
/nfsshare 192.168.0.2(rw) localhost(rw) 192.168.0.3(ro,insecure)
с самого себя экспортируемый каталог монтируется
(mount -t nfs localhost:/nfsshare /mnt/net - OK),
а с другого адреса если пытаюсь смонтировать,
то получаю :
mount -t nfs 192.168.0.1:/nfsshare /mnt/nfs
mount: RPC: Port mapper failure - RPC: unable to receive
В чём тут дело ?
-
Вобщем, после непродолжительного шаманства с ModeLine`ми стало
даже 101.8 Гц
-
может он и задавался неоднокрано, однако чё-то ни одного ответа,
где бы предложено было решение проблемы мне не попалось.
А просто наугад менять VertRefresh и HorizSync мне уже как-то надоело. Есть еще действенные рекомендации ?
-
Видяха - NVIDIA GeForce 4 MX разрешение 1024x768, частота обновления - выше 85 Гц никак не поднимается, хотя совершенно
достоверно известно, что и монитор и карта могут работать и на более высокой частоте развёртки. Как можно увеличить её до 100 Гц?
-
Как снести rpm`ом программу, которая состоит в списке зависимостей ? ситуация : есть старый gdb, идущий с дистрибутивом (/usr/bin/gdb) и новый, собранный из исходников,
стоит в /usr/local. Когда начинаю удалять rpm-установленный gdb
rpm блажит про кучу зависящих от него приложений. Как его надоумить, что-бы всё равно приложение было удалено?
-
Оказалось чего проще - скачать сырцы gdb и пересобрать -
родной видно чуток кривоват. Но - каждое решение плодит новые проблемы
-
У меня была такая проблема, когда мандрагора при установке почему-то обозначила виндовый раздел как скрытый НТФС (т. е. ид файловой системы стал вместо 0x07 0x17). проблема была решена
переустановкой идентификатора фс линуховым fdisk'ом
-
Ну дык есть ещё какие-нить соображения о том как ему мозги вправить ?
-
Мифическая зависимость :
$ldd a.out
linux-gate.so.1 => (0xffffe000)
libc.so.6 => /lib/tls/libc.so.6 (0x00ac8000)
/lib/ld-linux.so.2 => /lib/ld-linux.so.2 (0x00aaf000)
linux-gate.so.1 - файл, которого вобще нет нигде,
но без него приложение (и другие) исполнятся.
Может быть в нём причина этого косяка gdb, если да, как его
восстановить ?
-
Цитата: Цитата:
1. А как узнать какой файл добавлять в этот параметр?
Я так предпологаю, тот, который включается, т.е. библиотеку.
Ну дык а где его имя посмотреть ?
Как узнать какой файл "No such file or directory"
-
1. А как узнать какой файл добавлять в этот параметр ?
2. Все равно чё-то неправильно это так каждый раз запускать gdb.
Диалап
в Общий форум
Опубликовано
Уточнение по результатам самых последних экспериментов:
пингуются все адреса, кроме удалённого. И, похоже, не работает
разрешение имён узлов, т. е. ссылка http://217.23.144.36/
открывается нормально, пинг и трассировка на неё тоже проходит,
а на запрос в виде http://www.linux.ru/ получаю ответ : "unknown host name". И так со всеми узлами.